Clock spring replacement video

R51 specific technical questions & information

Moderator: Forum Administrator

Clock spring replacement video

Postby Kelzac » Fri May 19, 2017 4:38 pm

Howdy folks,

I'm about to try and replace the clock spring on my 51 and was wondering if anyone can link a video for some help.

Cheers community
Kelzac
 
Posts: 65
Joined: Tue Nov 24, 2015 9:49 am
Location - Town or City: Victoria point
Location - State: Queensland
Location - Country: Australia

Re: Clock spring replacement video

Postby Kelzac » Sat May 27, 2017 2:39 pm

So after a bit of searching on youtube, I couldn't find anything helpful. About the only thing I managed to learn was how to remove the airbag on a D40 video. However turns out the job is a piece of cake. Got it sorted in less than half an hour. Now I just need to get me an OBD II scanner so that I can clear the airbag warning light.
Kelzac
 
Posts: 65
Joined: Tue Nov 24, 2015 9:49 am
Location - Town or City: Victoria point
Location - State: Queensland
Location - Country: Australia

Re: Clock spring replacement video

Postby Pete » Sun May 28, 2017 10:30 pm

Well done
Pete
2014 200 Series TTD V8 LandCruiser VX with ARB winch bar, snorkel, OME Lift kit, polyairs, aftermarket exhaust, chip, & 275/70/18 Cooper ST Maxx. 2015 Lotus Freelander 196 caravan
(previously 2005 R51 Ti, previously 2000 R50 Ti)
User avatar
Pete
PCoA Administrator
 
Posts: 2032
Joined: Thu Dec 11, 2008 8:46 pm
Location: Gladesville, NSW
Location - Town or City: Gladesville
Location - State: NSW
Location - Country: Australia

Re: Clock spring replacement video

Postby NickJ » Mon May 29, 2017 10:56 am

Can get bluetooth OBD dongles and a good app to go with it on ebay for around $30

Nick
2004 Pathfinder TI, FWH, Front Lokka, 265/70-16 AT693 / 31" Bighorns, Pedders
2008 BT50 SDX. 31" Bighorns, front eLocker, ARB winch bar, ARB Canopy
1999 105 series Land Cruiser, front Lokka, FWH, Part-tome kit, ABR bar and winch, lift, Mickey Thompson ATZ
User avatar
NickJ
PCoA Administrator & VIC Rep
 
Posts: 1866
Joined: Mon Oct 30, 2006 4:08 pm
Location: Willow Grove - Victoria Closer to the High Country
Location - Town or City: Willow Grove - Victoria Closer to the High Country
Location - State: Victoria
Location - Country: Australia

Re: Clock spring replacement video

Postby Kelzac » Mon May 29, 2017 5:19 pm

Thanks for the advice. Any pointers on the best dongle and app?????
Kelzac
 
Posts: 65
Joined: Tue Nov 24, 2015 9:49 am
Location - Town or City: Victoria point
Location - State: Queensland
Location - Country: Australia

Re: Clock spring replacement video

Postby TheRightPath » Mon May 29, 2017 10:20 pm

Don't get a Bluetooth one if you are using Apple devices. Not compatible, or at least they weren't a few generations ago. I bought one when I had an android phone, but then switched to apple and had to drag the laptop out to the car when I wanted to see what was going on.
2011 ST-L with nudge bar, tow bar and upgraded audio to include rev cam and GPS.
TheRightPath
 
Posts: 72
Joined: Wed Oct 09, 2013 8:43 pm
Location - Town or City: Lake Macquarie

Re: Clock spring replacement video

Postby Kelzac » Tue May 30, 2017 5:59 pm

I have ben looking at the wi fi ones. They are cheap enough. Found one on Ebay for $13.
Kelzac
 
Posts: 65
Joined: Tue Nov 24, 2015 9:49 am
Location - Town or City: Victoria point
Location - State: Queensland
Location - Country: Australia

Re: Clock spring replacement video

Postby natrob18 » Sat Jun 24, 2017 5:03 pm

i didnt think you reset the ABS air light with the OBDII scanner. I have an OBDII scanner and is only for the check engine light codes.
natrob18
 
Posts: 15
Joined: Thu Jul 28, 2016 5:40 pm
Location - Town or City: Adelaide
Location - State: South Australia
Location - Country: Australia

Re: Clock spring replacement video

Postby wawan » Thu May 10, 2018 12:13 am

Hi,
I have watched several video about this. What I don't understand is how to set the clock spring to neutral position or the correct position? Have read the manual it should be 2.6 revolutions turns from the right end but still haven't got any clue to do this?
wawan
 
Posts: 5
Joined: Mon Jan 30, 2017 10:40 am
Location - Town or City: Perth
Location - State: Western Australia
Location - Country: Australia


Return to R51 Pathfinder (2005 to 2013)

Who is online

Users browsing this forum: No registered users and 2 guests